yield load

Farmers took several payments for each load of product and inflated their yield reports.

每批农产品,农民们都分好几次付款支付,并以此夸大其产量报告.

Inelastic yield load formula of axial compression middle long columns was deduced through the use of tangent modulus theory.

并用切线模量理论推导出计算钢管煤矸石混凝土轴压中长柱非弹性屈曲荷载的计算公式；

Studying bearing capacity including crack load, yield load and ultimate load, formability, wasted energy by testing load displacement stagnates time of curve and horizontal load strain of curve. 3.

通过试验墙板的荷载&位移滞回曲线、荷载-应变关系曲线，研究现浇剪力墙板和叠合式剪力墙板的承载能力（开裂荷载、屈服荷载、极限荷载）、变形性能和耗能能力。

The FEM calculation shows that with increasing loading rate, general yield load Pgy, stress and strain rate ahead of notches for the notched specimens increase.

有限元计算表明：缺口试样的整体屈服载荷Pgy，缺口前的应力，应变率均随加载速率的增加而增加。

The areas of hysteresis and yield load in KO group were ten and fourteen times greater respectively in Sham group.

治疗组滞后环面积、屈服载荷分别为阳性对照组的10倍、14倍。

Meanwhile, the failure load predicted by net section yield criterion of multiple cracks is presented.

同时采用了多处损伤剩余强度净截面屈服判据预测破坏载荷.

Modifying the yield line pattern in reference 〔 1 〕, a defect of the theoretical solution in reference 〔 1 〕 is mended, that is, with increasing the area of the steel plate, the load carrying capacity will increase to infinite.

改进了文献〔1〕的塑性铰线模式，修补了文献〔1〕的理论解的一个缺陷，即随着粘钢板的面积增加，承载力上升至无穷大。

Cracking load, yield load and ultimate load are obviously higher.

开裂荷载明显提高，屈服荷载和极限荷载均显著提高。

Coulomb yield-law is used to determine elastic and plastic limiting load of thick cylinder and thick sphere in strength-differential material.

本文利用库仑屈服准则，研究了拉压异性材料厚壁圆筒和厚壁球壳的弹性极限载荷和塑性极限载荷，得出了新的结果和结论。

Test results showed that for the specimens with large beam section width, a portion of tensile reinforcement in the front of the wall yielded, while reinforcement in the back of the wall did not yield at the peak load.

试验结果表明，达到最大承载力时，梁截面比较宽的试件，墙正面的部分受拉纵向钢筋屈服，墙背面的纵向钢筋未屈服；

On the basis of the YAI ( yield approach index) and PLI ( plastic load index), the new concept, FAI, is introduced.

结合屈服接近度（YAI）和塑性荷载指数（PLI）的概念，提出了破坏接近度（FAI）的新定义。

The lap joint produces bending effect under the action of tensile load and the bending degree decreases with the increase of yield limit of base material.

搭接接头在拉伸载荷作用下会产生折弯效应，折弯程度随被钎焊母材屈服极限的增加而减小。

It was pointed out that in tensile test with specimen of C-grade casting steel, the load-halt method or the judgment from the pointer swing of strain instrument could not give clearly the yield point except the graphical analysis method.

指出测定C级钢拉伸试样屈服点时，用载荷停顿法或指针法，屈服现象不明显，只有图解法可一次测出未知屈服指标。