camber

Inward tilt is negative camber and outward tilt is positive camber.

向内倾斜,是消极的拱和拱向外倾斜是积极的.

A taper has two sides, the underside is a circle, the flank is a camber.

结论:圆锥有两个面, 底面是一个圆形, 侧面是一个曲面.

A blended wing-body, variable camber wings, and forebody strakes provided extra lift and control.

翼身融合, 变曲率机翼, 还有前机身边条翼提供了额外的升力和控制性能.

Long lengths of unsupported strip camber tend to deviate from the horizontal or slope to side.

长距离无支持的钢带偏离水平线或偏向一侧.也可参见以下部分.

The tilt of the wheel ( camber ) is measured in degrees and is adjustable on many vehicles.

该轮 ( 弯度倾斜 ) 是衡量度,是许多车辆可调.

I can see a point, a circle and a camber.

生:有一个点, 有一个圆,还有一个曲面.

Camber line won " ts do orthogonal arc tooth wimble gear. "

中心线 不成 直角的弧齿锥齿轮.

The superstructure a depth of 3 ft . 6 in. a marked camber of 19 ft . 8 in.

上部结构的建筑高度为3英尺6 英寸,有19英尺8 英寸 显著的上拱度.

Second, the camber equation is developed for the crss points.

从曲面方程和直线方程的联立解求出交点.

The joint of all the camber will be the camber curve.

各截面凸度连线便是凸度曲线.

Compared with even die drawing, camber die-drawing's limit drawing coefficient is detracted, so efficiency is increased.

曲面凹模拉深与平端面凹模拉深相比, 降低了极限拉深系数,减少工序 、 提高了效率,降低了成本.

Determine the camber factor.

确定曲面的因素.

The larger permeability damage modulus and the earlier the IPR curving and the camber was.

渗透率伤害系数越大,曲线弯曲越早,弯曲度越大.

The method also permits inverse design with flaps , specification of geometric constraints ( thickness , camber, etc. ).

比如开发了边界层的形状参数,可以指定允许的最高表面上取消或延期举办层流 、 乎设计要求.

In this thesis the basic aspects about forming process of camber die are studied etically.

本论文对曲面凹模成形工艺的若干问题进行了系统的理论分析.

The main, sub-beam handover, the first main beam arch camber, arch camber beam after the meeting.

主 、 次梁交接时, 先主梁起拱, 后次梁起拱.

Camber is the inward or outward tilt of the wheel at top.

坎贝尔是在方向盘向内或向外倾斜的顶部.

It has two sides, one is a circle, the other is a camber.

生:圆锥有两个面, 一个面是圆形, 另一个面是曲面.

" To Camber Company, please . It's on 32 nd avenue . "

去 坎培克斯 公司. 在第32街上.

At present , the experience method of installing the camber has many problems.

经验法设置大跨径连续刚构桥预拱度存在诸多问题.

The thermal camber of rolls is a very important factor affecting distribution of hot strip mills.

轧辊热凸度是影响热带钢连轧机负载辊缝的重要因素,高效率的工作辊冷却水系统是生产高质量热轧板带的重要保证.

The automatic camber control system of the line is introduced completely in the paper.

本文将对该生产线的自动凸度控制系统作全面详细的介绍.

The camber is curvature of the cross section and the crown is the highest point camber.

图中向上倾斜部分是路拱,该部分的最高点是路脊.

Synopsis There are some factors that cause the formation hot strip side-camber in the rolling process.

板带轧制过程中因受某些因素影响会形成侧弯.

Camber line becomes orthogonal arc tooth wimble gear.

中心线成直角的弧齿锥齿轮.

The measures for improving wear of camber for lockup were proposed.

针对锁紧弧面的磨损提出了改善措施.

For straight-winged tailless airplanes, only the negative camber satisfies the conditions for flight.

对直机翼无尾飞机, 只有负弯度才满足飞行条件.

The front subframe is modified for extra camber and castor.

前副车架被修改为额外拱形和蓖麻.

Application of low Mooney viscosity, non pollution type NBR to thin camber sponge rubber was studied.

研究低门尼粘度 、 非污染型丁腈橡胶在薄型曲面海绵胶料中的应用.

This provides an increased damping rate and allows a slight reduction in camber angle.

这样就增加了减震度,并且可以稍微减少外倾角.