tooth profile

The value of tooth deformation is the key-influencing factor on machining accuracy of tooth profile.

轮齿的形变情况是决定齿形加工精度的因素.

Profile Variation is any variation from the specified tooth profile normal to the flank.

齿形误差:齿形误差是特定的齿廓相对齿侧的任何公差.

The Influence of Tip Circle's Error on the Measuring Accuracy of Portable Tooth Profile Instrument

齿顶圆误差对上置式齿形仪测量精度的影响

On Design of the helical hob of involute& cycloid composite tooth profile gear

摆线渐开线复合齿形滚刀设计

The revertex mechanical bit general many are the heterogeneous bit, mainly has each kind of tooth profile even Yuan Dao and the strip forming tool.

塑胶机械刀片一般多为异型刀片，主要有各种齿形平元刀及条型刀。

Research on wearing capacity of composite tooth profile

复合齿形齿轮的耐磨性研究

The Tooth Profile Equation of the Internal of Shifting Drive Bearing

变速传动轴承内齿圈齿廓方程的分析

The Study on Seeking the Cycloid Tooth Profile Modifier by Non-linear Curve Fitting Method

利用非线性曲线拟合法搜寻摆线轮齿廓修形量的研究

It is proved by practice that machining straight tooth-shaped holes with the designed slotting cutter not only has high efficien-cy, but also reaches the required tooth profile precision of machined work piece.

通过实践证明，利用设计的插齿刀在插齿机上加工直线齿形孔，不但效率高，而且被加工零件的齿形精度达到了图纸要求。

Pitch Point is the intersection of the spline tooth profile with the pitch circle.

节点是键齿的齿廓与节圆的交点.

Parameterize Tooth Profile Slope Deviation Measuring Uncertainty in Gear Measuring Center Standard

齿轮测量中心标准中齿廓倾斜偏差测量不确定度参数的确定

Compound Modification Method and Its Optimizational Design of Cycloid Disk Tooth Profile

摆线轮齿形的组合修正方式及其优化设计

Double circular arc spiral bevel gear is applied to heavy truck drive axle of the need for bearing capacity and dynamic characteristics of two aspects of research, its bearing capacity in the coal mine scraper conveyer reducer of circular arc tooth profile has been verified.

双圆弧弧齿锥齿轮应用到重卡驱动桥中需要对承载能力和动态特性两方面进行研究，其承载能力在煤矿刮板输送机圆弧齿廓减速器研究中已经得到了验证。

Design of Obligue Tooth Slotting Cutter with Asymmetric Tooth Profile of Rake Face

前刀面为非对称齿形的斜齿梳齿刀的设计

Research on Measuring Uncertainty Parameter of Tooth Profile Slope Deviation

齿廓倾斜偏差测量不确定度参数的确定

A systemic analysis has been made for meshing properties of the straight conjugating internal gear pair in this paper, involving the solution of conjugated tooth profile, meshing process and line of action, as well as the influences of gear designing parameters on the contact ratio.

对直线共轭内啮合齿轮副的啮合特性进行了全面分析，包括共轭齿形的求解、啮合过程分析和重合度计算及齿轮参数对重合度的影响等内容。

Pitch Point is the intersection of the spline tooth profile with the pitch circle.

节点是键齿的齿廓与节圆的交点.

Method for eliminating 3-shaped contact zone on gear tooth profile

齿轮之字形接触区的消除方法

Influence of Front Rake of the Slotting Cutter on the Tool Endurance and Tooth Profile Error

插齿刀前角对刀具耐用度及齿形误差的影响

In this paper, a new type tooth profile of sprocket has been given from the study of designing the bobber's axial section.

本文首先从设计滚刀的轴向截形入手，提出了链轮的新齿形；

This article introduced the double pin roll breaker's survey and the tooth profile and the roller tooth arrangement design situation analysis briefly.

介绍了双齿辊破碎机的概况和齿形与辊齿布置设计情况。

This paper gives the new technique of tooth profile on the normal section of nobbing-shaving cutter involute worm which is imitated by hyperbola and suggests that axial section of grinding wheel can be obtained in hyperbolic form by dressing conical surface of grinding wheel along the inclined straight line.

给出了用双曲线拟合滚剃刀渐开线蜗杆法剖面齿形新技术，提出了锥面砂轮按斜直线进行修整，能够获得砂轮轴截面为双曲线形状。

The QX straight conjugate internal gear pump is a new type of hydraulically driving element. The calculation of tooth profile, the limiting point of meshing, the designing process of slotting cutter were introduced.

介绍了一种新型液压动力元件&QX型直线共轭内啮合齿轮泵的齿廓曲线计算、专用插齿刀具设计方法，分析了齿廓啮合极限点。

This method is much simpler than conventionally used enveloping method, and gives a basis for processing the tooth profile of the internal gear of the shifting drive bearing.

这种方法比传统的包络法简便，概念清楚，对变速传动轴承内齿圈的廓形加工，具有重要的指导意义。

The part of z ≤ 41 is comparatively complex, and it has the cutting tooth profile which is of the fewness tooth in processing by milling machine.

z≤41齿形设计比较复杂，小齿数的齿轮铣削加工又有根切。

In this system, the geometric figure of the enveloping tooth profile is generated.

通过滚齿加工过程图形仿真系统可以精确地获得齿廓曲线.

Finally, a comprehensive summary is conducted to the tooth profile error, axial error, accumulative pitch error in gear shaving.

最后，对剃齿加工对工件齿形误差、齿向误差、周节累积误差等进行了较为全面的总结。

The tooth profile precision of carbon alloy slotting tool with cone rake face is analyzed, the carbon alloy slotting tool with convex rake face is put forward and compared with the slotting tool with cone rake face.

分析了锥形前刀面硬质合金插齿刀齿形误差，提出一种凸曲前刀面硬质合金插齿刀并对二者的齿形精度进行了比较。

The method of how to calculate the profile quantity in tooth profile trace is proposed.

提出求解径向剃齿刀齿形、齿向修磨量的方法.

A Simple Method for Designing Tooth Profile of Generating Hob-The Space Engaged Tooth Profile Normal Line Method

展成滚刀齿形设计的简易方法&空间啮合齿廓法线法