temperature zone

The results show that alkali metal silicate is decomposed into alkali metal steam that rises with gas in the high temperature zone.

结果表明：在高温区，碱金属硅酸盐大量分解形成碱金属蒸气随煤气上升；

It is revealed that the system is metal behavior under low temperature zone ( T < high temperature zone ( T> Tp).

研究此系列体系的导电特性，表明体系在低温（T＜＜T p）是金属导电行为，在高温（T＞T p）有明显的半导体特性。

With the increase of friction coefficient, the area of high temperature zone and the stress at the inlet of the corner increased;

随着摩擦系数增大，核心高温区面积增大，转角入口区的应力也有所增加；

In the high temperature zone, the variation gradient of measured values for concentration field of gas compositions is greater than that of calculated ones.

在高温区，煤气组分浓度场实验值的变化梯度大于计算值。

The high temperature zone is characterized by high carbon dioxide concentration and low oxygen concentration.

温度场与各组分场有着对应关系，高温区对应CO2高浓度区和O2的低浓度区；

Study on Soil Erosion under Different Temperature Zone in Loess Plateau by GIS

基于GIS的不同温度带的黄土高原土壤侵蚀研究

Sea Ice Impacts on the Formation of Muddy Tidal Flats in the Temperature Zone& A Case Study of Jiangsu Coast

海冰对温带淤泥质潮滩发育的影响&以江苏弶港潮滩为例

Comparison of Maize Varieties with Cultivation Technique of Partial Ridge Permeability in the Third and Fourth Accumulated Temperature Zone

第三四积温区玉米偏垄通透栽培品种对比试验

When the air leakage strength changed, the high temperature zone location and scope would be changed.

在改变漏风强度后，高温区位置和范围也会随之改变。

Corrosion and Protection of the Piping at Low Temperature Zone Heated Side of Industrial Boiler

锅炉低温受热面管的腐蚀及防护

The re-division about the quantity of heat resources and the accumulated temperature zone of Heilongjiang Province

黑龙江省热量资源及积温带的生新划分

The Probability Analysis of Converter off Gas Explosion in the Middle Temperature Zone

转炉煤气中温段爆炸可能性的计算与分析

The experiments have shown also that most of cracks take place in temperature zone of brittleness ( about 800 ℃ for 45 steel).

试验还证实，纵裂多发生在钢的中温脆性区（45钢约为800℃左右）。

Analysis on Combining Ability of Main Agronomic Characters in Improved Maize Inbred Lines from Temperature Zone Maize Germplasm

温热种质改良玉米自交系主要农艺性状配合力分析

The Study on CO-2's Dynamic Change in High Forest in the Karst Eco-system of Temperature Zone in Summer

夏季温带岩溶生态系统中乔木林内的CO2动态变化研究

LST presented downward trend and the percentage of middle temperature zone was enlarged in the eight years.

8年间地表温度呈下降趋势，高温区、次高温区、低温区百分比减小，中温区百分比增大。

Effect of Brittle Temperature Zone Process on Cracking in Medium and Heavy Plates

脆性温度区工艺对中厚板裂纹的影响

And annual wetting time in proportion to each temperature zone.

年润湿时间在各温度段所占的比例。

Utilization of New Temperature Zone for Cold Storage of Foods

低温保藏食品新温度带的利用

Design and Simulation of Temperature Controller for Calcining Zone of Rotary Kiln

回转窑煅烧带温度控制器的设计与仿真

A mathematical model on the shaft differential heating temperature zone theoretical calculation

轴类件差温加热温度场理论计算的数学模型

Determination and Theoretical Analysis of the Constant Temperature Zone in Mines

矿区恒温带参数的确定及理论分析

Drawback of vertical tubular air preheater is the greater corrosion of tubes at the low temperature zone due to cold air inlet.

立式管式空气预热器的缺点，是冷风进口处的管束低温腐蚀严重。

Comments on the Horizontal Tubular Air Preheater for Recovery of the Heat of Flue Gas and Reducing Corrosion at Low Temperature Zone

卧式管式空气预热器在锅炉烟气余热利用及耐低温腐蚀方面的探讨

Study on the Impact and Attrition of Blending Elastopolymer Under High Temperature Zone

共混聚合物弹性体在高温区域的冲击、磨损状况下的研究

The operative temperature range is much wider than the comfort temperature zone in ASHRAE 55 standard, and the PMV index is not always consistent with the actual situation.

学生可接受的作用温度范围比ASHRAE标准规定的舒适区温度范围要宽得多，PMV指标与实际情况存在较大差别。

The experiments results of different heating rate show that TG curves move to high temperature zone with the increasing of heating rate.

不同升温速率的实验结果曲线表明，提高升温速率，TG曲线向高温方向移动；

The annealed strip is cooled to the temperature required by galvanizing process in the cooling zone and then goes into zinc pot through sealed channel.

将退火带钢在冷却段冷却到指定温度，经密封通道进入锌锅。

As with mechanical ventilated buildings, comfort zone in naturally ventilated buildings presents a larger temperature range.

与机械通风相比, 自然通风具有更大的舒适区.

With the increase of the extrusion speed, billet temperature and die temperature was gradually increased. The highest temperature was located in bearing export while the flow dead zone located in diversion hole of die and the stress of bearing have sharp risen.

随着挤压速度的增加，坯料的温度和模具的温度逐渐上升，温度最高的地方在出口工作带上，模具的导流孔的圆角部分存在流动死区，工作带的应力急剧升高。