section thickness

According to the standard, the specimen with prefabricated fatigue crack has a standard 3 points bending shape that has a rectangular section of B × 2B ( B: specimen thickness) and notch orientation of thickness direction.

取尺寸为B（板厚）×2B、缺口方向为板厚方向、带预制疲劳裂纹的标准试样进行三点弯曲试验。

Counted the number of luteum and cystic follicles, measured the thickness of thecal cells and granulosa cells in general HE staining section.

卵巢切片常规HE染色，计算每张切片黄体数、囊状卵泡数、囊状扩张卵泡比例，进行卵泡膜细胞层最大厚度及颗粒细胞层最大厚度的显微测量。

Based on the clay degradation temperature and casting section thickness, the degradation region can be determined directly, and the consumption coefficient can be calculated.

由材料的失效温度及铸件的壁厚，直接找到该材料的失效距离，从而计算其损耗系数。

Study on wall thickness distribution in thickened section of stretch reduced pipe

张力减径管端增厚段壁厚分布规律的研究

Presents the calculation method of the draught, minimum height, section size, thermal stretching, compensation and insulating layer thickness of the chimney and gives calculation examples of insulating layer thickness.

介绍了燃油锅炉房附壁烟囱抽力、最低高度、横断面尺寸、热伸长及补偿量、保温层厚度等的计算方法，给出了保温层厚度计算实例。

It is shown by the result that the increase of thickness of the covering plates can not only effect on the bearing capacity of components remarkably but also decrease likewise the displacement and twist of the cross-section of covering-supported components under the action of static load.

结果表明，蒙皮板厚度的增加不仅显著影响构件的承载能力，而且可明显减小蒙皮支撑柱在静力荷载作用下截面的位移和扭转；

The crash tests of different thickness, number, length steel panel and different section, number, length, thickness square column are simulated.

对不同厚度、不同数量、不同长度的受冲钢板，以及不同剖面尺寸、不同板厚、不同数量的方形梁进行了仿真分析研究。

The analysis method which can calculate the stress of the changing wall thickness section connecting the sphere head and the cylinder shell with unequal wall thickness has been established.

建立了通过变厚度筒壳把球壳与不等厚的筒壳相连接的不连续应力解析计算方法。

By setting up mechanical model, the relationship of curve radius, jacking force and effect factors such as pipe diameter, length of pipe section, thickness of wooden piece, elasticity of material and the difference of jack displacement is investigated.

通过建立力学模型对曲线路线半径R、顶推力P和影响因素如管径D、管节长L、木垫片厚a、材料弹性模量E以及工具管油缸行程差（b-c）等的关系进行推导。

According to numerical simulation and molten steel solidification mechanism, in the paper, the restrict relationship had been setup between casting speed and molten steel level and average mould tapping section thickness as well as its shell temperature at tapping spout.

本文基于数值模拟和钢液凝固机理，建立起结晶器内钢液液位和铸坯拉速对其出钢口处钢液截面平均温度和坯壳温度的制约关系。

Plain CT scans were performed with a section thickness and interval of 2 mm followed by enhanced scans after intravenous bolus injection of 70 ml 60% ultravist.

CT扫描层厚、层距各2mm，平扫加60%优维显70ml静脉团注后增强扫描。

Controlling thickness tolerance of cast-rolling slab along transverse section

铸轧铝板带坯横向厚差的控制

Prepare paraffin section of the line HE staining of each group of mice auricles to observe the histological differences and the changes of the auricle epidermis thickness and total thickness of mice auricle with microscope. Results: 1.

制作各组小鼠耳廓的石蜡组织切片行HE染色，并在显微镜下比较各组组织学变化及各组耳廓表皮厚度和总厚度的变化。

Study on Dimensional Accuracy of High Strength Gray Iron Cylinder Block Castings with Thin Section Thickness

高强度薄壁灰铸铁缸体铸件尺寸精度研究