mild steel

DN3 series spot welder is widely utilized in the spot welding of mild steel, corrosion resistant plate and round wire in the industries such as panel beating, light fittings and hardware appliances.

系列点焊机同样广泛应用于钣金，灯具，五金电器行业中低碳钢、不锈钢板和圆丝的点焊。

Wire Materials: Mild steel wire, stainless steel wire, galvanized steel wire, hot-dipped zinc plating iron wire.

丝材料: 低碳钢线, 不锈钢丝, 镀锌钢丝, 热浸镀锌铁丝.

Make a Mobius strip out of a ribbon of mild steel and magnetise it.

用一根软钢条做成麦比乌斯带，将其磁化。

Corrosion rate of mild steel under wet dry alternate conditions by means of 0.

研究了模拟工业酸雨大气条件下低碳钢经干湿循环加速腐蚀实验条件下的锈蚀速度变化.

For mild steel immersed cyclically in seawater,-0.95 V ( SCE ) was suggested as the protective potential criteria.

推荐海水间浸低碳钢的阴极保护电位判据为-0.95V ( SCE ).

Mild steel has a high tensile strength, this being 200 times that of concrete.

低碳钢具有很高的抗拉强度, 大约是混凝土的抗拉强度的200倍.

In this paper, a novel electrochemical technique under thin water film, combined with dew test and surface roughness measurement, were utilized to study the atmospheric corrosion performance of cold-rolled mild steel plates.

采用薄层电化学测试技术，并结合结露试验和表面粗糙度测量研究了冷轧低碳钢板的耐大气腐蚀性能。

Mild steel has a high tensile strength, this being about 200 times that of concrete.

软钢的抗张强度大, 约为混凝土的200倍.

The potential of zero charge ( ZCP) was determined by electrochemical impedance measurements and the adsorption model of CM-chitosan on mild steel surface was established.

用电化学阻抗法测定了碳钢在盐酸溶液中的零电荷电位，确立了CM-chitosan的吸附模型。

Arange of mild steel thickness up to 6 mm can be easily punched.

并能轻易地冲压各种厚度达6毫米的软钢.

Mild steel rod, specifically designed for the professional player.

软钢铁杆, 专为职业球手而设计.

Mild steel is usually used for general engineering purposes.

软钢通常用在一般工程上.

On the performance and manufacture technique aluminium/ tin alloy& mild steel composite products

铝锡合金/低碳钢复合材料性能及工艺研究

Nickel-plated mild steel round head machine screw wire line thimble

镀镍低碳钢圆头机器螺丝绕扎钢丝绳头用的长圆形铁环

Some proposals about prepassivation of mild steel equipments in hot potassium carbonate CO _ 2-stripping systems are suggested.

从理论上对热钾碱脱碳系统碳钢设备的预钝化工艺提出了建议.

Be able to weld mild steel . alloy steel etc.

适合碳钢,合金钢,软钢等,可用多种焊丝.

We weave and trade in wire mesh of stainless steel, mild steel, copper, bronze, monel, inconel.

我们编织和贸易在铁丝网的不锈钢, 低碳钢, 铜, 青铜, 蒙乃尔, 镍.

Thickness of mild steel shall be adequate and shall not be less than 2.5 mm.

低碳钢的喷绘的厚度应该适当,并不得少于2.5毫米.

Correspondingly, a visual window used for welding mild steel with Ar and CO_2 shielding gases is determined. On the basis of this principle, a visual system of welding robot is developed and applied to production practice for rear axles of automobile.

确定了Ar弧焊及CO2气体保护焊在低碳钢母材上的相应观察窗口，由此开发出焊接机器人视觉系统，并在汽车后桥上得到应用。

Mold base can be of mild steel or aluminum.

模座可以用一般的钢材或者铝.

The friction stir welding of Aluminum alloy with copper and mild steel was conducted.

进行了铝合金与工业纯铜、铝合金与低碳钢的搅拌摩擦焊接实验.

The carbon content of mild steel is much lower than cast-steel.

软钢的含碳量要比铸钢的低得多.

Nowadays, although there are many producing methods of stainless steel inner-clad mild steel bimetallic tube, a simple effective method is to be invented.

现有的生产不锈钢／碳钢双金属复合管有好多方法，但是都具有相对局限性。

The resistance spot welding process of mild steel was studied by experimental and finite element methods.

采用试验和有限元数值模拟的方法,对汽车车身低碳钢电阻点焊的过程进行了研究.