meshing的例句大全

The meshing requirement of finite element model theand the calculating method of heat flux are expatiated.

采用焊接仿真用到的经典高斯热源模型,设计了基于表参数热流密度加载算法.

Installation error will cause the bevel gear meshing error in low-load or overload conditions, the actual contact length is less than or greater than the theoretical contact length.

安装误差会引起锥齿轮副啮合误差，在低载或重载条件下，实际接触长度小于或大于理论接触长度。

Then, the theoretical meshing arcus length and the simutaneous meshing tooth numbers of four tooth and two tooth difference harmonic drive are analyzed.

对双波四齿差和二齿差谐波齿轮传动的理论啮合弧长和可能同时啮合的齿对数进行了分析比较；

Through the kinematic and dynamic analysis on the mechanism, it is found that the variations of speed, acceleration and dynamic tension of the chain while meshing with sprockets are closely related to three parameters: chain speed, chain pitch and tooth numbers of the sprockets.

对该传动装置进行了运动学和动力学分析，认为链条在与链轮啮合时的速度、加速度及动态张力的变化都与链条的速度、节距、链轮的齿数这3个参数有密切的关系。

In this article the bearing ability test of hard gear face point-line meshing gear transmission and the trial of noise test are introduced.

本文介绍了硬齿面点线啮合齿轮传动的承载能力试验和噪声测定试验的情况。

A systemic analysis has been made for meshing properties of the straight conjugating internal gear pair in this paper, involving the solution of conjugated tooth profile, meshing process and line of action, as well as the influences of gear designing parameters on the contact ratio.

对直线共轭内啮合齿轮副的啮合特性进行了全面分析，包括共轭齿形的求解、啮合过程分析和重合度计算及齿轮参数对重合度的影响等内容。

The results show that three sets of prototype all have higher efficiency, double-disc cycloidal gearing can work well with larger axial loads, and can also adjusted the meshing clearance by adjusting the axial location of the meshing pair.

实验结果表明，三台减速器均具有高的传动效率，双圆盘摆线行星传动样机可以承受较大的轴向载荷，双圆盘锥形摆线行星传动通过调整啮合零件轴向位置可以调整啮合的间隙。

Initial study has been done, such as design and machining of gear set, selection of meshing medium, calculation for the transmission and so on.

作为国家自然科学基金的一项基础研究项目，已经在带式啮合介质齿轮副的设计、介质带材料的初步选择、齿轮传动的计算等方面进行了初步的探索。

Meshing Theory and Application Study of Grinding Gear with the Toroidal Involute Interior Thread Worm Grind Wheel

TI内螺纹蜗杆砂轮磨齿的啮合理论及应用研究

The time-variant meshing stiffness also causes large dynamic load in gear pairs.

时变啮合刚度还导致了较大的动载荷；

Because of the meshing stiffness of a gear pair, the governing equation denotes a linear dynamic system with periodic time-varying coefficient.

由于齿轮副啮合刚度的影响，动力学方程式代表了一个具有时变系数的线性动力系统。

The causes of phase variation in air supply obtained after analysis are mainly errors in manufacture, abuse in operation and errors in repair. Several adjusting methods for correct installation of timing gears, inspection of meshing clearance of gear faces and adjustment of valve clearance are suggested.

分析了配气相位变化的原因主要是制造误差、使用不当和修配误差等，提出了正确安装正时齿轮、检查齿面啮合间隙和调整气门脚间隙等几种调整方法。

The essential meshing relationship, position of instantaneous center and the meshing range of the tooth head arc are discussed.

讨论了内外转子的基本啮合关系、瞬心的位置以及外转子齿顶圆的啮合范围等。

Having found out the transition point on the gear slotting cutter, the authors discuss several cases of interference when the internal meshing gears are slotted and give the checking formulae.

本文在确定了插齿刀过渡点的基础上，讨论内齿轮副插齿加工时的几种干涉情况，并给出了校验公式。

The QX straight conjugate internal gear pump is a new type of hydraulically driving element. The calculation of tooth profile, the limiting point of meshing, the designing process of slotting cutter were introduced.

介绍了一种新型液压动力元件&QX型直线共轭内啮合齿轮泵的齿廓曲线计算、专用插齿刀具设计方法，分析了齿廓啮合极限点。

According to the non-backlash meshing basic relation ship and the requirement of equality of addendum reducing coefficients, the paper applies computational methods of computer programming and cut-and-try to determine the modification coefficient of idle gear in ordinary gear train.

本文依据无侧隙啮合基本关系和齿顶降低系数相等的要求，应用计算机编程计算和计算器试凑计算方法，确定定轴轮系惰轮的变位系数。

Transitional-zone method in hexahedral finite element meshing in geotechnical engineering

岩土工程数值分析中的过渡区方法

Meshing and Remeshing Techniques for Hexahedral Mesh in the Finite Element Simulation of Plastic Forming

塑性成形有限元模拟六面体网格划分和再划分技术

The normal lines of the cam pitch curve at the meshing points intersect at the instantaneous center of the cam and the pin gear, which accords with the meshing principle of tooth contour.

在凸轮与针轮啮合的瞬时，各针齿与凸轮啮合点处，凸轮理论廓线的法线交汇于该瞬时凸轮与针轮的速度瞬心，符合齿形啮合基本定理。

In addition, the tooth profile of spiral bevel gear is spherical involute and the tooth surface is irregular space curved face which make it difficult to establish the accurate 3D models. The simulation analysis of meshing and optimization design of spiral bevel gears is greatly hindered.

同时弧齿锥齿轮齿廓形状为复杂的球面渐开线，齿面也为不规则的空间曲面，三维几何精确建模较为困难，导致其啮合仿真分析以及局部优化设计的相关研究工作难以开展和深入。