curing time

Dan Zufen moisture curing, the curing time is not reduced, good flexibility, and strong anti-deformation.

单组份有机硅湿气固化, 固化时不收缩, 弹性佳, 抗 形变能力强.

The specific gravity, liquid limit and plastic limit, plasticity index of acid pollution laterite decrease with accrescent acid concentration and extended curing time.

酸污染红土的比重、液塑限与塑性指数随酸浓度的增大和养护时间的延长总体都呈减小的趋势。

The results showed that the curing time of product extended when the heat diffusivity decreased;

结果表明，热扩散系数降低时制品的硫化时间延长；

The results showed that the test temperature had certain influence on the Mooney viscosity, Mooney scorch time and curing behavior of rubber compound;

结果表明，试验温度对胶料的门尼粘度、门尼焦烧时间和硫化特性均有一定影响。

The selection of process conditions such as the dosage of binder SX in pigment printing, curing temperation and curing time was discussed.

探讨了粘合剂SX在印花工艺中用量、焙烘温度、焙烘时间等条件的选择。

With the increase of curing time, the strength of hardened cement increases continually in the later of the reaction period.

随养护时间增长，混合材料后期强度持续增加。

Study on tye Decrease of Autoclave Curing Time for Aerated Pfa Concrete

缩短粉煤灰加气混凝土蒸压养护时间的研究

An Experiment Study on the Influence of Air Content and Curing Time on Concrete Anti-Chloride Permeability Performance

含气量和养护龄期对混凝土抗氯离子渗透性能影响的试验研究

The strength of filling body, filling mortar weight concentration and curing time are in direct proportion relationship.

且充填体的强度与充填砂浆重量浓度、养护时间之间均成正比例增加关系，没有出现异常情况。

In order to use shrub materials to produce wood based panels reasonably, pH value, buffering capacity and curing time of 6 main shrub species in the north western China were measured.

为了合理开发我国西北地区的沙生灌木，研究了内蒙西部地区沙柳、柠条、沙棘、红柳、桦棒、杨柴6种主要沙生灌木的pH值、酸碱缓冲容量与UF胶混合物固化时间。

Test and Study of Influence of Curing Time on Features of a Lime-flyash Soil Project

养护龄期对二灰土工程特性的影响试验研究

Experimental Study of Influencing Factors of Cement Curing Time

水泥候凝时间及其影响因素的试验研究

Come through the curing temperature by differential scanning calorimetry ( DSC), Curing trial in combination with curing reaction appropriate curing time.

通过差式扫描量热法（DSC）得出固化温度，并结合固化试验得出固化反应适宜的固化时间。

The optimize curing time under different temperatures was also investigated.

另外，对不同养护温度下土壤聚合反应的最佳养护时间也进行了研究。

In this paper application of "static placing in heated room" has been proposed as a means for decreasing the autoclave curing time of aerated pfa concrete.

本文提出了采用热室静停作为缩短粉煤灰加气混凝土蒸压养护时间的手段。

The compressive strength also varied with the curing time.

养护时间不同，其抗压强度有明显的差异。

Epoxy resin grouts have low viscosity, good grouting property and the coagulation or curing time of their serosity can be regulated according to the demand.

环氧树脂化学灌浆材料由于其灌浆材料粘度小，可灌性好；浆液的胶凝或固化时间可以按需要进行调节；

And as the curing time extended, the hardness, tensile strength and elastic modulus of SBR ebonite increased and its T_g rose significantly.

随着硫化时间的延长，硬质SBR的硬度、拉伸强度及弹性模量增大，玻璃化温度显著提高。

Influencing of curing time on film hardness is discussed through modifying the ratio of paint and curing agent. The defects from spraying process and the countermeasures are narrated.

通过调整漆与固化剂比例，讨论了固化时间对漆膜硬度的影响，同时论述了喷涂过程中产生的缺陷和采取的措施。

Laboratory experiment is carried out on the mechanical property of CFG pile material ( fly ash concrete) composed of a large quantity of ⅲ a-fly ash mixture. The relationships between compressive strength and the proportion of fly ash substituting cement, and curing time are studied.

通过材料实验，对大掺量Ⅲa级粉煤灰素混凝土构成的CFG桩桩身材料进行力学性能方面的试验研究，主要探讨抗压强度与材料配比、龄期之间的关系。

In order to develop a resin fitting to glue for construction, ZSL and DCPD were introduced into resin simultaneity. The modified resin has excellent property of mechanics, curing time, dynamic viscosity, air dry and corrosion resistance.

ZSL与DCPD两种改性剂同时引入树脂中，协同作用使树脂的力学性能十分优越，且树脂的固化时间、粘度、气干性、耐腐蚀性能均十分突出。

It can be quicky cured and resisted high temperature for class H in a short curing time and low evaporation losses.

它耐高温达到H级，固化速度快，贮存周期长，挥发率低。

Take the average temperature in the curing time as curing temperature.

养护温度取各湿喷桩养护期的平均气温。

Prolonging curing time may lower the crosslinking density.

硫化温度的提高会使交联密度下降.

Low temperature and high vacuum tumble technology being widely used at home and abroad can shorten the curing time and improve product textural properties.

低温真空滚揉能缩短腌制时间，改善产品质构，目前国内外广泛采用；

As to this type of lightweight soil, direct shear test is used to study the influencing factors of cement content, EPS beads content and curing time on the shear parameters.

通过直接剪切试验，获取了淤泥EPS颗粒混合轻质土的抗剪强度参数，即粘聚力与内摩擦角。

Determination of Curing Temperature and EV Time for Thick walled Rubber Article

橡胶厚制品硫化温度与等效硫化时间的测定

This paper studies the effect of curing time and filling on mechanical property of mouse pad.

研究了硫化时间、补强剂对鼠标垫力学性能的影响。

Experimental results show that with crisscross winding method and 30% to 40% of resin content and 150 N to 200 N of winding tension for a fiber strand and GPC chart analysis to determine curing time, better comprehensive performance of the composite materials can be obtained.

结果表明：采用交替铺层方式缠绕成型，含胶量控制在30%～40%（质量分数），缠绕张力控制在150N～200N，采用GPC谱图控制固化时机，得到的复合材料综合性能较好；

The key consideration and the pouring temperature of the concrete under low temperature construction, curing temperature, heat storage and holding time parameters on the maximum temperature rise inside the concrete, as well as the size of the surface tensile stress, and draw some useful conclusions.

重点考虑和阐述了混凝土在冬季施工下的浇注温度、养护温度、蓄热保温时间等参数对混凝土内部最高温升以及表面拉应力大小的影响，得出了一些有益的结论。