camshafts

Structural Analysis and Improvement of the Base Plate in High Speed Camshaft Grinder

高速凸轮轴磨床垫板的结构分析与改进

Only turn engine using the crankshaft pulley, not at the camshafts.

仅能使用曲轴皮带轮转动发动机，而不是在凸轮轴处转动。

If one of the camshafts cannot be locked, loosen all the fastening screws on the affected camshaft sprocket by about one turn.

如果有一根凸轮轴无法锁定，则松开相应凸轮轴链轮上的所有紧固螺钉（旋转一圈左右）。

Variable-speed grinding of camshaft based on constant removal rate

基于恒磨除率的凸轮轴变速磨削研究

Since the engine has no valves, it doesn't need any camshaft, valve lifters and so on.

因为发动机没有阀门，它不需要任何凸轮轴、起阀器等。

Distribution: two overhead camshafts, 16 valves.

分布：两个顶置凸轮轴，16气门。

Finally, this paper collects all technique links of above vision measurements together. Under laboratory conditions, gauge block size and axial size between prefabricated camshafts are measured respectively to test measurement accuracy of vision measurement structure size.

最后，本文将上述视觉测量的各个技术环节集成在一起，在实验室条件下，分别测量量块的尺寸和装配式凸轮轴凸轮间的轴向尺寸，以检验视觉测量结构件尺寸的测量精度。

Design and Simulation of Assembled Camshaft's Mandrel Automatic Transportation System

装配式凸轮轴芯轴自动上料系统的设计及仿真

Manufacturing Techniques and Application Status of P/ M Assembled Camshaft

PM组合式凸轮轴的制造工艺及应用现状

Design Analysis and Test Research on System of Camshaft and Valve

配气系统的设计分析与试验研究

Camshafts, Rockerarm, Rocker Shaft, General Casting Automotive Parts, Components and Spares.

采购产品凸轮轴, 摇臂,摇臂轴, 一般铸造汽车零件, 部件和零件.

Some high-performance engines have two separate camshafts, one for each set of inlet and exhaust valves.

一些高性能发动机有两个单独的凸轮轴, 分别负责开关进气门和排气门.

Automatic Measurement of Camshaft and Evaluation of Data Processing ( 2)

凸轮轴的自动测量及数据处理评定方法（2）

Never twist the camshafts when the chain tensioner is removed.

切勿在拆下链条预紧器时扭转凸轮轴。

Friction Welding and Post Heat Treatment for 45 Steel Camshafts

45钢凸轮轴摩擦焊接及焊后热处理

Never apply forces across the camshafts in the timing drive mechanism.

切勿对正时传动机构中的凸轮轴施力。

Technology of variable speed grinding and speed measurement of camshaft

凸轮轴变速磨削与转速测量技术

Production and Application of Fully Chilled Cast Iron Camshaft with High Properties

高性能全激冷铸铁凸轮轴的生产和应用

Failure analysis and improvement for camshaft in high pressure oil pump

高压燃油泵凸轮轴失效分析与改进

A Sort of New Detection Method of Grinding Burn of Camshaft

一种用于凸轮轴磨削烧伤检测的新方法

Further engine modifications also include precision-machining the cylinder heads and fitting them with four special camshafts.

进一步的修改还包括发动机精密加工的气缸盖和装修有四个特别凸轮轴他们.

Certain engines with overhead camshafts have timing belts that have a limited life span.

顶制凸轮轴结构的汽车发动机都配备了正时皮带,并且这个皮带的生命周期是有限的.

Machining precision of camshaft with domestic automated NC camshaft grinding machine is far from satisfaction, so imported equipments are applied to the manufacture of camshafts, but it leads to a high cost.

我国全自动数控凸轮轴磨床加工的凸轮轴精度往往达不到要求，故凸轮轴的加工主要依靠进口设备，但进口设备售价相当昂贵。

Influence of Process Factors Stability on Quality of Chilled Cast Iron Camshaft

工艺因素稳定性对冷硬铸铁凸轮轴质量的影响

The Study and Design on Camshaft Wearing Based on Exhaust Braking

基于排气制动的凸轮轴磨损研究与设计

Research and Software Development of Dynamic Optimization and Simulation of Camshaft NC Grinding Process

凸轮轴数控磨削加工过程动态优化仿真的研究及软件开发

Study of Structure Properties and Process Optimization of Chilled Iron Camshaft

激冷铸铁凸轮轴组织性能研究及铸造工艺优化

A New Method of Phase Correlation for Signal Processing Camshaft Grinding Goes High-Tech

相位相关技术研究高精凸轮轴磨削

Cast-iron Camshaft Manufacture Technology and Development Status at Home and Abroad

铸铁凸轮轴制造技术及国内外发展动态

Analyzing the grinding characteristics of camshaft grinding machine model S

S型凸轮轴磨床磨削特性的分析